Intel HS-2601A Instrukcja Użytkownika

HS-2601A Intel Low Power Mobile 500MHz Mini Board Computer •3.5” Size•All-in-One•CRT/Panel•LAN•WDT• •DOC•2 USB•IrDA•PC/104•Flash Disk• •PCI Bus Mini

41.3 Board Dimensions

5Chapter 2 Unpacking 2.1 Opening the Delivery Package The HS-2601A is packed in an anti-static bag. The board has components that are easily damaged

6It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring t

7Chapter 3 Hardware Installation This chapter provides the information on how to install the hardware using the HS-2601A. This chapter also contains

83.2 Board Layout

93.3 Jumper List Jumper Definition Default Page JP1 Watchdog Timer Active Type Select Short 2-3 20 JP2 Panel Voltage Select Short 1-2 12 JP

103.6 System Memory The HS-2601A provides one SO-DIMM socket at location U2. This onboard memory socket can support 64MB, 128MB and 256MB SO-DIMM mod

113. Once you have figured out where the pin 1 locations are on both chip and socket, align the module’s pins on an upright angle against the socket

123.8 VGA Controller The HS-2601A has an onboard jumper that selects the working voltage of the flat panel connected to the system. Jumper JP2 offers

13 CN10: 50-pin Panel Connector PIN. Description PIN Description 1 +12V 2 +12V 3 GND 4 GND 5 3.3V / 5V Note 6 ENAVDD 7 ENAVEE 8 GND 9 P

CCCooopppyyyrrriiiggghhhttt DDDiiisssccclllaaaiiimmmeeerrrsss The accuracy of contents in this manual has passed thorough checking and review bef

143.9 IDE Drive Connector CN12, a 44-pin connector, provides the PCI E-IDE drive provisions onboard. A maximum of four IDE drives may be connected o

153.10 Floppy Disk Drive Connector The HS-2601A uses a standard 34-pin header connector, CN11, for floppy disk drive connection. A total of two FDD

163.11 Serial Port Connectors The HS-2601A offers two NS16C550 compatible UARTs with Read/Receive 16byte FIFO serial ports and two internal 10-pin h

17122625PD0PD2PD4PD6ACKJPEAFDJINITJGNDGNDGNDGNDGNDSTBJPD1PD3PD5PD7BUSYSLCTERRJSUNJGNDGNDGNDGND 3.13 Ethernet Connector The HS-2601A provides one exte

183.15 USB Connector The HS-2601A provides one 8-pin connector for USB0 & USB1 port connections at location CN13.  CN13: USB Connector PIN Des

19 CN5: 2-pin Power Input Connector PIN Description 1 +5V 2 GND 12 3.18 Keyboard/Mouse Connectors The HS-2601A offers two possibilities for keybo

20LD1 and JP3 are the Keylock and Reset Button connectors onboard.  LD1: Power LED PIN Description 1 +5V 2 GND 12  JP3: Reset Button Connector PI

21After an Enable cycle of WDT, user must immediately execute a Refresh cycle to WDT before its period setting comes to an end every 1, 2, 10, 20, 11

223.21 CompactFlash Connector The HS-2601A also offers an optional CompactFlash connector which is IDE interface located at the solder side of the

233.22 Mini PCI Connector HS-2601A supports a Mini PCI interface which is a very popular notebook computer expansion interface for Modem, Video, LAN

Table of Contents Chapter 1 General Description ---------------------------------6 1.1 Major Features ----------------------------------------------

24PIN. Description PIN. Description 71 AD[7] 72 3.3V 73 3.3V 74 AD[6] 75 AD[5] 76 AD[4] 77 RESERVED 78 AD[2] 79 AD[3] 80 AD[0] 81

253.23 PC/104 Connectors The PC/104 expansion bus offers provisions to connect all types of PC/104 modules. With the PC/104 bus being known as the ne

26 CN2: 64-pin PC/104 Expansion Slot PIN Description PIN Description 1 IOCHECK* 33 GND 2 SD7 34 RESETDRV 3 SD6 35 +5V 4 SD5 36 IRQ9 5 S

27Chapter 4 Award BIOS Setup The HS-2601A uses Award PCI/ISA BIOS for the system configuration. The Award BIOS setup program is designed to provide t

284.2 Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PageUp> and <PageDown> k

294.3 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from se

30 Load Setup Defaults The chipset defaults are settings that provide for maximum system performance. While Award has designed the custom BIOS to ma

314.4 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard

32 Primary Master/Slave & Secondary Master/Slave Drives: The categories identify the types of 4 channels that have been installed in the compute

33 LCD&CRT: The category selects the type of video adapter used for the system monitor. Although secondary monitors are supported, you do not ha

3.17 Power Connectors ----------------------------------------------- 18 CN1: 4-pin Power Connector ----------------------18 CN5: 2-pin Power Input C

344.5 BIOS Features Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s

35NOTE: Many disk diagnostic programs that attempt to access the boot sector table can cause the above warning message. If you will be running such a

36 Boot Up Floppy Seek: During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 760K, 1

37 Typematic Rate (Chars/Sec): When the typematic rate is enabled, this selection allows you select the rate at which the keys are accelerated. 6

38 Report No FDD For WIN 95: Whether report no FDD for Win 95 or not. The available choices are Yes, No.  Video BIOS Shadow: Determines whether vi

394.6 Chipset Features Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset m

4050ns DRAM Timing Type 60ns DRAM Timing Type  EDO CASx# MA Wait State: You could select the timing control type of EDO DRAM CAS MA (memory addre

41Enabled Video BIOS access cached Disabled Video BIOS access not cached  Video RAM Cacheable: Select Enabled allows caching of the video RAM , r

42 Power-Supply Type: This item allows you to select the type of power supply installed to your board. The available choices are Auto (for auto-dete

434.7 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operatin

SSSaaafffeeetttyyy IIInnnssstttrrruuuccctttiiiooonnnsss Integrated circuits on computer boards are sensitive to static electricity. To avoid dama

44 Power Management: This category allows you to select the type (or degree) of power saving and is directly related to the following modes:  Doze

45 MODEM Use IRQ: This item determines the IRQ in which the MODEM can be used. The available choices are 3, 4, 5, 7, 9, 10, 11, NA. 4.7.1 PM Timers

46 PowerOn by Ring: An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) awakens the system from

474.8 PNP/PCI Configuration This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/

48 Assign IRQ For VGA/USB: This option turns on or off the IRQ assignment for both VGA and USB ports. 4.9 Load BIOS Defaults When you press <Ent

494.10 Load Setup Defaults When you press <Enter> on this item you get a confirmation dialog box with a message similar to the figure below. T

504.11 Integrated Peripherals The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationshi

51 On-Chip Primary/Secondary PCI IDE: The integrated peripheral controller contains an IDE interface that supports a single IDE channels. Select Ena

52 IR Transmission delay: Full duplex mode permits simultaneous bi-directional transmission. Half duplex mode permits transmission in one direction

534.12 Supervisor/User Password Setting ROM PCI/ISA BIOS (2A69KD2L) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHER

This page intentionally left blank.

54When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from ch

554.14 Save & Exit Setup Pressing <Enter> on this item asks for confirmation: Pressing “Y” stores the selections made in the menus in CMOS

564.15 Exit Without Saving Pressing <Enter> on this item asks for confirmation: Quit without saving (Y/N)? Y This allows you to exit Setup wi

57Chapter 5 Software Utilities This chapter contains the detailed information of IDE, VGA, Audio and LAN driver installation procedures. 5.1 VGA Dr

583. Select the setting page, click on the Advanced properties button. 4. Press the Change button in the adapter area. 5. Click on Next to continu

5911. After the system has restarted, you can go back into the display applet and select alternate screen resolutions and color depths. NOTE: Instal

604. In the Change Display Type window, click on Have Disk. 5. Specify the path to the new driver and press the <ENTER>key (if in driver A:,

619. After restarting, check on the VGA driver and make sure the properties of the driver look similar to the following figure.

625.3 LAN Driver Installation for WIN95 & WIN98 5.3.1 Win98 Windows 98 will detect the network driver automatically therefore there is no need

635. Specify the path the new driver and press <ENTER> key (if in driver a:, type a:\). If you’re not sure exactly where the drivers are, choo

1Chapter 1 General Description The HS-2601A is a 100MHz Intel® BX chipset-based Mini PCI Bus Intel Mobile board. With features such as enhanced I/O

645.4 LAN Driver Installation for Win NT4.0 1. Click the Start button, then go to Setting and click on Control Panel. 2. Click on the Network ico

659. Once the installation is completed, the system must be shut down and restarted for the new driver to take effect. 10. After restart, confirm th

66This page intentionally left blank.

2To ensure the reliability in an unmanned or standalone system, the Watchdog Timer (WDT) onboard HS-2601A is designed with pure hardware that does no

31.2 Specifications  CPU: Intel Low Power Mobil CPU from 500-800 MHz  Bus Interface: Mini PCI Local Bus  Memory: One SO-DIMM socket supporting