Intel 430TX Instrukcja Użytkownika

Intel 430TX PCI ChipsetIntelligentMAIN BOARDATX586forDual CPUs ATX FactorTX2forAT Factor / Wide SCSIUSER’S MANUALversion 1.0

10Map of ATX586 Mother Board Default Setting for Intel Pentium 133Mhz,AMD K5-133,CYRIX P166+ ,512K PB Cache1.2 Two-Jumper Setting for CPU

11JP6/JP7: Set CPU External Bus Frequency Rate (BF1, BF0)JP6/JP7: 1-2, SHORT forIntel 90/100Mhz, MMX233Mhz, AMD K5 75-133,AMD K6 PR233MhzJP6: 1-2 and

12JP8/9: Set CPU External Bus Frequency Selection (FS0, FS1, FS2)JP8: 1-2 and JP9: 2-3SHORT : 75Mhz for CX200+JP8/9:1-2 SHORT: 66Mhz for CX 166+, AMDK

13JP15: 2MB FLASH BIOS ONLY2-3 SHORT for normal (set by factory).Default.1-2 SHORT reserved for factory set only.JP16: Select FLASH BIOS2-3 SHORT for

14JP12: Choose CPU SMI Mode1-2 SHORT: SMI by PIIX4 ( Single CPU request SMI),Default.2-3 SHORT: SMI by IOAPIC (Dual CPU request SMI)1.4 Install Sys

158MB * 32 DS X 64MB8MB * 32 DS 1MB * 32 SS 72MB8MB * 32 DS 2MB * 32 DS 80MB8MB * 32 DS 4MB * 32 SS 96MB8MB * 32 DS 8MB * 32 DS 128MB16MB * 32SS X 128

16JP17: IR, fast infrared port. PIN-1: IRRX, PIN-2:GND; PIN-3: IRTX; PIN-4: VCCCOM1-2/CN1-CN5: Support 16550 high speedserial ports/ UART.PS/2 Mouse

17IDE 1: Primary IDE port to support ATAPI Mode 5IDE devicesIDE 2: Secondary IDE port to support ATAPI Mode 5IDE devices.FDC/CN8: Support 2 FDD up to

18JP8 Set CPU External Bus Frequency (FS0, FS1, FS2)JP9 Set CPU External Bus Frequency (FS0, FS1, FS2)JP12 Choose CPU SMI ModeJP13 2-3 Normal CMOS, 3-

19

2UPDATE INFORAMTIONJULY 22, 971) When you install ATX power supply, please connect CASESTANDBY to front panel connector CN9/JP9 , pin 19-20Power On.

20Chapter 2AWARD, PnPGREEN BIOSSETUP2.1 BIOS SetupPowe on the computer and press <DEL> key immediatelyand the screen will display you CMOS S

21of hard disk drive installed in the system, floppydrive type, and the type of display monitor.ROM PCI/ISA BIOS (2A59GT4A)STANDARD CMOS SETUPAWARD S

22OS Select for DRAM>64MB: NON-OS2F7 : Load Setup Defaults2.4 Chipset Features SetupROM PCI/ISA BIOS (2A59GT4A)CHIPSET FEATURES SETUPAWARD SOFTWAR

232.6 PNP/PCI ConfigurationROM PCI/ISA BIOS (2A56GT5A)PNP/PCI CONFIGURATIONAWARD SOFTWARE, INC.Resources Controlled By : Manual PCI IRQ Actived By :

24POST(hex)DescriptionC0 1. Turn off OEM specific cache, shadow...2. Initialize all the standard devices with default values standard devices inclu

253. Read CMOS data into BIOS stack area4. PnP initializations including (PnP BIOS only)-Assign CSN to PnP ISA card-Create resource map from ESCD5. As

261E If EISA NVM checksum is good, execute EISA initialization(EISA BIOS only)1F-29 Reserved30 Detect Base Memory & Extended Memory Size31 1. Test

2750 Write all CMOS values currently in the BIOS stack area backinto the CMOS51 Reserved52 1. Initialize all ISA ROMs2. Later PCI initializations (PCI

2863 1. If there is any changes in the hardware configuration, update the ESCD information (PnP BIOS only)2. Clear memory that have been used3. Bo

29Chapter 3Quick Installation GuideUltra IDE DriverandUpdate Flash BIOSfor Intel TX ChipsetThise Chapter includes two parts: one is to instal Enhance

3CONTENTPreface ... 1CHAPTER 1 Hardware Installation forATX5864 1.1 One Jumper to

30[If using OEM Version of Windows 95 CD-ROM on PIIX3 basedsystems see also " 82371SB PIIX3 Application Note #3 MicrosoftWindows 95* Support for

31******************************************************************************INTRODUCTION**********************************************************

321. The system must contain a supported Intel processor and chip set configuration:Chip set: Intel 430FX, 430HX, 430TX, 430VX and 440FX chipsets

3303/28/97 12:00a 6,128 _SETUP.DLL03/28/97 12:00a 179,689 _SETUP.LIB**************************************************

346. Click 'Yes' if you agree to continue. NOTE: If you click 'No',the program will terminate.7. Select 'INSTALL'

35This installation verification procedure is specific only to the version ofthe driver and installation file included in this package.This subsection

36 As a result, the individual controller descriptionsmay vary slightly from what is listed above. In thiscase, select the closest match.

37 de-installing the driver.1. Check the System Requirements. Windows 95* must be fullyinstalled and running on the system prior to running t

38 NON-WIZARD directions: A. Select 'Windows default driver', A "New HardwareFound" dialog box will request a driver l

39 accessed in a PCI Bus Master IDE fashion. Contact thedevice manufacturer for more information.2. Verify the length of the cables that are b

4 2.6 PNP/PCIConfiguration...18 2.7 IntegratedPeripherals...18 2.8 AWARD BIOS PostCode..

40 For example, C:\WINDOWS\SYSTEM\IOSUBSYS3. Select the driver file, "IDEATAPI.MPD".4. Open the "File" menu.5. Click

41The Intel driver does not support the following types of device in thesystem: - ATAPI Tape Drives - ATAPI CD-ROM Changer Drives - ATAPI DVD

42Advanced CD-ROM applications/features have not been tested withthis driver. This driver does not support Microsoft SMART IOCTLAPI and any mobile ID

43 the driver. - Any software translation mechanisms, such as Ontrack Disk Manager*, EZ-Drive*, or master boot record hooking.*********

44 Torisan* CDR-C3G NEC* CDR272 Torisan* CDR-S1G NEC* CDR273Q2> There is an Exclamation(!) or Question(?) mark next

45Q4> One or more of the IDE/ATAPI drives on the system fail toperform correctly and/or is not recognized by the driver.A4> Ensure devices on

46A6> Do not install the driver on a system equipped with these CD-ROM drives. There are no plans to support these drives withthe PIIX Bus Master

47 To workaround the issue, you can create a custom startupconfiguration that loads CD-ROM real-mode driver. The gamewill run in exclusive MS-DO

48VERSION 2.64 RELEASE*********************************This subsection describes the Intel PIIX Bus Master IDE Driver forWindows 95*, Version 2.64 (Ma

494. Added support to use BIOS Disk Services INT13h, function 08h, todetermine fixed disk drive geometry parameters.5. Added documentation clarificati

5CHAPTER 4 Hardware Installation for TX2 49 4.1 One Jumper to Set CPU...… 50 4.2 Two Jumper to Set CPU...…………… 52 4.

50Seagate*: ST5660A ST5850A ST51080A ST31220A ST31270A ST32140AWestern Digital*: AC2420 AC2510 AC2700 AC2850 AC31000

51 CR-583-BSanyo*: CRD-S54PSony*: CDU55E CDU76E CDU77E CDU311-GITEAC*: CD44E CD56EToshiba*: XM5302B XM5602B XM5702***

52does Intel make a commitment to update the information containedherein. Intel reserves the right to make changes to this document atany time, withou

53PART II. Update Flash BIOSBecause the BIOS of Pentium Triton main board is Flash BIOS, thereare two methods to update BIOS. Before programming the

54Chapter 4Hardware Installation For TX2TX2 is for AT platform for single processors design, including EnhanceI/O chip (SMC 669 compatible) resulting

554.1 One Jumper to Set CPU , Simple JumperNo more CPU jumper setting when you useIntel 133Mhz,CYRIX 166+,AMD K5-133 CPU.You just install CPU direct

56Map of TX2 Mother Board Default Setting for Intel Pentium 133Mhz,AMD K5-133,CYRIX P166+ , 512K PB Cache

574.2 Two-Jumper Setting for CPUJP8: Set CPU External Bus Frequency Rate (BF0, BF1)JP8:1-2/4-5, SHORT for Intel90/100Mhz, MMX 233Mhz,AMD K5 75-133, A

58JP5: Set CPU External Bus Frequency Selection (FS0, FS1)JP5: 1-3/2-4 SHORT: 55Mhzfor CX133+JP5: 1-3 SHORT : 60Mhz forCX 150+, Intel/AMD90/120/150/18

59JP10: CMOS. When you forget the password, clear CMOS,restart!2-3 SHORT for normal. Default.3-4 SHORT to clear CMOS (power must be off).OPEN for ext

6PrefaceInside the DocumentThis document describes setup ATX586 Dual Pentium Main Board withIntel 430TX PCI CHIPSET, resulting in Ultra IDE performanc

60SIMMs can be 60ns or 70ns Fast Page Mode (FPM), or EnhancedData Out (EDO) (BEDO & Parity are not supported). SIMMs mustbe installed in pairs so

614.5 Install IDE, Enhanced I/O and Front Panel ConnectorsThere is a special design that JP9 is for Key Lock, Sleep/Resume SW,Speaker, IDE LED, TB S

62ATX POWER CONNECTOR/J1: For ATX factor style power supplyAT POWER CONNECTOR/J2: For normal AT style power supplyPS/2 Mouse J4: PS/2 mouse port. 5-pi

63I/O Address and IRQOn Board I/O Address IRQ DRQGAME 200-20F X XCOM1 3F8-3FF 4 XCOM2 2F8-2FF 3 XCOM3 3E8-3EF 3 XCOM4 2E8-2EF 3 XIDE1 1F0-1F7 14 XIDE2

64J3 Key Board ConnectorJ4 PS/2 Mouse ConnectorJ5 COM2 PortJ6 COM1 PortJ7 Parallel PortJ8 Floppy Drive PortJ9 SCSI PortJ10 Wide SCSI PortJ11 IR Connec

65Pin-4 RTS, Request To Send Pin-4 (OUT)Pin-2 TXD, Transmit Data Pin-5 (OUT)Pin-5 CTS, Clear To Send Pin-6 (IN)Pin-20 DTR, Data Terminal Ready Pin-7 (

7(Chapter 4 is about positions, jumpers and connectors for TX2.Due to the board supports full range of Pentium CPU MMX 75Mhz-233Mhz, AMD K5/K6-PR233

8² 24 Programmable Interrupts: 13 ISA supported; 4 PCI; 1 interrupt/SMI# rerouting; 2 motherboard ; 1 interrupt used for INTR input; 3general purpose;

9Chapter 1Hardware Installation For ATX5861.1 One Jumper to Set CPU , Simple JumperNo more CPU jumper setting when you use Single ProcessorIntel 13